# Letöltési és feltöltési sebesség szabályozása. 0 esetén nincs korlát. ADSL esetén a feltöltés a kapcsoaltunk sebességének 80%-a legyen! Az értékek kbájt/secben legyenek megadva.

download_rate = 0
upload_rate = 50

# Egyszerre hány torrent fájlt töltsünk fel.
#max_uploads = 15

#Ezen port tartományban figyel a program
port_range = 5500-5600

# Torrentek leállíása ha már csak a megadott üres hely van
schedule = low_diskspace,5,60,close_low_diskspace=100M


# 
# /home/Torrents/Downloading
# /home/Torrents/Complete
# /home/Torrents/TorrentFiles/Auto
# /home/Torrents/Downloading/rtorrent.session
#

# Maximum and minimum number of peers to connect to per torrent.
#min_peers = 40
#max_peers = 100

# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 50

# Default directory to save the downloaded torrents.
directory = /mnt/HD_a2/Torrent/

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /mnt/HD_a2/Torrent/watch/

# Watch a directory for new torrents, and stop those that have been
# deleted.
schedule = watch_directory,5,5,load_start=/mnt/HD_a2/Torrent/watch/*.torrent
schedule = untied_directory,5,5,stop_untied=/mnt/HD_a2/Torrent/watch/*.torrent

# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,stop_on_ratio=200,200M,2000

#execute_log = /home/Torrents/rtorrent.log

# When the torrent finishes, it executes "mv -n <base_path> ~/Download/"
# and then sets the destination directory to "~/Download/". (0.7.7+)
#on_finished = move_complete,"execute=mv,-u,$d.get_base_path=,/home/Torrents/Complete/ ;d.set_directory=/home/Torrents/Complete/"

# The ip address reported to the tracker.

#ip = 127.0.0.1
#ip = 192.168.0.7

# The ip address the listening socket and outgoing connections is
# bound to.


# Start opening ports at a random position within the port range.
#port_random = no

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
check_hash = no

# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = no

# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
encryption = allow_incoming,enable_retry,prefer_plaintext

#
# Do not modify the following parameters unless you know what you're doing.
#
# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
hash_read_ahead = 8

# Interval between attempts to check the hash, in milliseconds.
hash_interval = 10

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
hash_max_tries = 5

# Max number of files to keep open simultaniously.
max_open_files = 128

# Number of sockets to simultaneously keep open.
#max_open_sockets = <no default>

send_buffer_size = 1M
receive_buffer_size = 25K


# Example of scheduling commands: Switch between two ip's every 5
# seconds.
#schedule = "ip_tick1,5,10,ip=torretta"
#schedule = "ip_tick2,10,10,ip=lampedusa"

# Remove a scheduled event.
#schedule_remove = "ip_tick1"

encoding_list = UTF-8
#scgi_local =/ffp/tmp/rpc.socket
schedule = chmod,0,0,"execute=chmod,777,/ffp/tmp/rpc.socket"
scgi_port = 127.0.0.1:5000

#http_proxy = 192.168.0.10:3128